How To Remove Pex Pinch Clamp

Being conscientious when removing the stainless steel pinch clamps allows for the plumbing equipment to be reused. A fitting that has been removed and is in expert shape tin can be used in some other arrangement saving money.

In this blog we are going to cover how to remove the pinch clamps by 2 bones methods Pick #1 Cutting the ear of the pinch clamp u sing a n E nd- C utter , and Option #2 U sing mutual tools to disengage the interlock tabs of the clench  using a S ide  C utter P liers and a F lat South crew D river. For instructions on how to make a stainless steel pinch clamp PEX connection, click hither.

Tools Required

• Pipe Cutter
• Heavy  D uty Eastward nd C utter
• Pliers
• If you do not have a northward E nd C utter you can use S ide C ut  P liers and a F lat H ead South crewdriver.

Getting Started

Removing a stainless steel p inch clamp with a heav y duty terminate cutter is quite simple . However, if you do not take a n end cutter, no worries it can be done with side cutting pliers and a apartment screwdriver .

In hard to accomplish locations, when a compression clench needs to be removed with the plumbing equipment in the system, t he use of a  heavy duty stop cutter can make the job easier. Clamp removal is easie st  if the fitting tin exist removed from the piping system and clamped in a vice , it is important to avert clamp ing  on the inser t   ribs or spinous area, which will damage the fi t t i ng m aking it unusable.

Option #i

Removing a Pinch Cl a mp  using a northward End Cutt er.

Step #ane

Cut the fitting assembly from the PEX pipe using a pipe cutter. The
cut should be close to the fitting. Leavin g  approximately ½" - iii/4" of pipe tin brand it easier to get a grip on the pipe with a pliers to p ull the pipe from the plumbing equipment in step iii.

Step #2

Place cut jaw on each side of clamp ear . Squeeze h andle southward until the jaws cutting completely through the clamp  ear .  And then g rip ane of the cutting ends with the jaws to open and remove the clamp from the pipe.

Step # 3

Remove the PEX Pipe. The barbs on the PEX fittings make removing the pipe difficult, grip on the PEX pipe with a pliers, and with a twisting movement remove the pipe from the plumbing fixtures. You may need to cut part fashion through the pipe in guild to get the pipe to come off, keen intendance must be taken to not cutting right through and impairment the fitting.

Option # 2

Removing a Compression Clamp u sing common tools to disengage the interlock tabs of the clench.

Step # i

Cut the plumbing equipment associates from the PEX pipe using a pipage cutter. The
cutting should be close to the fitting. Leaving approximately ½" - 3/4" of piping can make it easier to get a grip on the pipe with a pliers to pull the pipage from the plumbing fixtures in step four .

Step #ii

Work a flat spiral driver or side cutter jaws under the clench ring tab and pry the finish up to dis engage and split the interlocking tab mechanism.

Step # 3

Using a side cutters or pliers grab onto the tab and pull to fully open the clench band and remove the clamp.

Step #four

Remove the PEX Piping. The barbs on the PEX fittings make removing the pipage hard, grip on the PEX pipe with a pliers, and with a twisting motion remove the pipe from the fitting. Yous may need to cutting part way through the pipe in order to go the pipe to come off, great intendance must be taken to not cut right through and damage the plumbing equipment.

No matter which selection y'all choose, the pinch clamp can't be used once again but the fitting can be. Before throwing away the fitting away, consider these steps to remove the pinch clamp and reuse the fitting. E'er make sure the fitting is in good shape before reusing it.

Have farther questions nearly this subject?

Caput over to Boshart's Knowledge Base: technical product data, guidelines, and more.

Source: https://blog.boshart.com/how-to-remove-a-pex-stainless-steel-pinch-clamp

Share this post